Boat Outfitting - Tools

Multi-Tool with Knife Blade - 304 Stainless SteelThis handy Multi-Tool includes a knife, needle nose pliers, cutters, scissors, various screw drivers, bottle opener, file, and saw. Constructed of corrosion resistant stamped 304 stainless steel. A must have for every tool bag! Includes canvas carrying...

Add-A-Snap - Black - 4" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State...

NAVDoctor NMEA Network Diagnostic ToolNMEA 2000 networks are used extensively for interfacing marine electronic products. It’s based on a robust Canbusarchitecture, but one bad device, cable or termination can have a detrimental effect on performance. Fault finding can be time consuming and tricky.NAVDoctoris a...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

AT-5 Large White Nylon Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength...

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is...

1.25" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter....

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

Plastic Suction Cup HandleInjection Molded Nylon/Nitrile-Buna Rubber Portable, dual suction cup handle installs instantly. Mounts in any direction on any non-porous surface. Easily mount and re-mount with no marks or damage to hull. No holes, screws, or tools required. Ideal for cleaning waterlines or boat...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Marine Digital Corrosion Professional Tester with Silver & Silver Chloride Reference Cell (SSC)The corrosion protection system on your boat should be checked at regular intervals. Failure to do so can lead to a costly and time consuming repair. Seaguard Digital Corrosion Tester is designed...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...